Electrical distribution

Strain gauge signal conditioner

09 July, 2009 | Supplied by: Weidmuller Pty Ltd

The ACT20P-Bridge strain gauge signal conditioner and isolator provides four switch-selectable input ranges of 0 to ±10, 20, 30 and 50 mV and proportional analog output of between 0-22 mA with loads of <600 Ω, and 0-11 V with loads >1 kΩ. Accuracy is claimed as being better than 0.05%, with a temperature drift of better that 50 ppm over the range of -40 to +70 °C.

Protective relay testing

09 July, 2009 | Supplied by: Megger Limited

To enable electrical installations and relays to be tested to the new IEC 61850 international communication standard for electricity substations, an IEC 61850 option has been introduced for the MPRT protective relay test system, together with MGC configurator software.

Flange mounting enclosures

09 July, 2009 | Supplied by: Stahlin Non-Metallic Enclosures

A full flange accessory option is available for the DiamondShield series of nonmetallic enclosures, providing improved mounting versatility in positioning enclosures to fit onto poles, struts or walls in both indoor and outdoor applications including harsh corrosive and industrial environments.

Energy storage batteries

09 July, 2009 | Supplied by: Valen Power Pty Ltd

The SEC TSG range of 12 V sealed lead acid batteries deploys Monobloc Catalyst technology for long-life operation, thereby combining the safety and low-maintenance advantages of sealed lead acid batteries with the long life of normal lead acid batteries.

Watertight enclosures

09 July, 2009 | Supplied by: Hammond Electronics Pty Ltd

The 1457 extruded aluminium family of small enclosures has been expanded with the introduction of RFI-screened IP54 environmentally sealed versions. The 1457 E series is designed to house PCBs and small electronic, electrical or pneumatic components.

Field termination M12 connector

09 July, 2009 | Supplied by: Harting (HK) Limited

The Field termination M12 connector enables the installer to choose between two different kinds of termination methods, making it adaptable to suit differing field situations and conditions. A wide range of shielded cables can be terminated onto the connector.

Shielded M8 cord sets

09 July, 2009 | Supplied by: Turck Australia Pty Ltd

The M8 picofast cord sets are now optionally available as a completely shielded unit by connecting a braided shield directly to the coupling nut. This provides a reliable connection with 100% cable and connector shielding, which protects against electromagnetic and radiofrequency interference.

Liquid-tight tubing and fittings

09 July, 2009 | Supplied by: NPA Pty Ltd

The Heyco range of Flex III liquid-tight tubing and fittings has been expanded with the release of 3/8- and 1-inch sizes.

Cable bushings and grommets

09 July, 2009 | Supplied by: NPA Pty Ltd

The Heyco Products LabKit provides wire protection for cable entry points into prototype development of electrical and electronic systems and equipment.

Switch cover plates

09 July, 2009 | Supplied by: Legrand Australia P/L

The Linea Soft-Touch cover plates are a series of coloured fascias that can be snapped onto the Linea GPOs and switch plates, maintaining their low 4 mm thick profile.

High-density power hub

09 July, 2009 | Supplied by: Pepperl+Fuchs (Aust) Pty Ltd

The FieldConnex 500 mA high-density power hub is an addition to the FieldConnex fieldbus interface products, designed for fast installation and reliable long-term operation in a fieldbus infrastructure.

Transformer analyser

09 July, 2009 | Supplied by: Power Parameters Pty Ltd

The Serveron continuous, online, dissolved gas analysis monitor for transformers is available in two models, both based on closed-loop gas chromatography.

Quick-disconnect sensors

09 July, 2009 | Supplied by: Turck Australia Pty Ltd

The range of FM-approved 12, 18 and 30 mm 3-wire DC barrel sensor and cordset combinations has been expanded to include quick-disconnect sensors that may be used in Class I, Division 2, Groups A, B, C and D environments when equipped with a Turck lokfast guard. Sensors with potted-in cable for use with conduit are also FM approved for these locations.

Chemical resistant connectors

09 July, 2009 | Supplied by: Soanar Limited

The Anderson Power Products CR-SB (chemical resistant) SB range of high-current, quick-disconnect power connectors was developed for industrial applications that require robust connector solutions resistant to environmental factors that commonly degrade standard products, leading to eventual failure.