Testo 880-3 thermal imager
25 March, 2009 | Supplied by: TechRentals
The Testo 880-3 is a thermal imager that uses infrared radiation which can visualise defective insulation, thermal bridges, building defects and damage, as its temperature resolution is less than 0.1 °C, so that even the smallest temperature can be seen.
Proof of maintenance on transformers for insurers
12 March, 2009
Conducting a regular transformer testing and maintenance program could assist in reducing costly business insurance premiums.
32-channel power quality recorder
26 February, 2009 | Supplied by: http://www.techrentals.com.au
The Hioki 8826 measures 32 analog and logic signals simultaneously. It is used to acquire data. This can include monitoring electric signals, detecting ground fault, recording short loss of power, testing load shutdowns in power plants or for general R&D or manufacturing applications.
Voltech PM 1000+ precision power analyser
03 February, 2009 | Supplied by: Westek Electronics Pty Ltd
The Voltech PM 1000+ precision power analyser is suitable for single-phase power and energy measurement of power circuits, industrial and domestic appliances, linear and switchmode power supplies and can also be used to measure inrush parameters under zero-crossing or peak values (using Voltech PS 1000 Inrush Switch).
EX600 series true RMS clamp meters
03 February, 2009 | Supplied by: Teledyne FLIR
The EX600 series of true RMS clamp meters features an IR thermometer for locating hot spots and NCV, making it an all-in-one solution for both electrical and HVAC professionals.
Analyser for renewable energy systems
03 February, 2009 | Supplied by: Yokogawa Australia Pty Ltd
The WT500 power analyser addresses renewable energy systems with the capability of simultaneously measuring DC and AC signals and calculating system efficiency. Separate integrate functions are also included to enable evaluation of charge/discharge and bought/sold power in photovoltaic systems.
Industrial electrical and automation testers
03 February, 2009 | Supplied by: Fluke Australia Pty Ltd
The ScopeMeter 225C and 215C test tools perform verification of electrical signal quality on industrial buses like Fieldbus, CANbus, Profibus and Modbus.
Bus terminal I/O multimeter
03 February, 2009 | Supplied by: Beckhoff Automation Pty Ltd
The Beckhoff digital multimeter terminal adds measurement functions to its I/O system. Using the instrument with a fieldbus interface for measuring current and voltage, measured values can be processed directly in the I/O system or by the master controller. These dynamic measuring terminals are available for both the Beckhoff Bus and EtherCAT terminal systems.
Clamp-on AC logger
03 February, 2009 | Supplied by: AEMC Instruments
The Simple Logger II Model CL601 is a battery-powered, 1-channel recording device with an alkaline battery pack. Line tracking is performed such that 64 samples over one line cycle are taken. Harmonic measurements are calculated from these 64 samples. Frequency tracking is performed over the range of ±2 Hz around the nominal line frequency (50 or 60 Hz).
3D thermal imaging software
03 February, 2009 | Supplied by: Fluke Australia Pty Ltd
Version 2.0 of the SmartView software for Fluke thermal imagers provides 3D imaging capability and additional options to optimise and organise thermal images and create professional reports.
Audio lead tester
03 February, 2009 | Supplied by: Soundcorp Pty Limited
The Quest LT01 cable tester is designed to test for polarity (phase reversal) and continuity in a variety of analog and digital audio leads and cables.
Cable certification and ethernet tester software
03 February, 2009 | Supplied by: Keysight Technologies Australia Pty Ltd
An advanced network test option for the WireScope Pro cable certification tester has been released for the validation and pre-qualification of voice over IP services and to stress test ethernet connections.
Digital multimeters
02 February, 2009 | Supplied by: Eaton Electrical (Australia) Pty Ltd
The Kyoritsu digital multimeter range comprises four models: 1051, 1052, 1061 and 1062 and features colour-coded range selection switches and function buttons for ease of use.
Web forum for commercial and industrial facilities to achieve energy savings
16 January, 2009
A new web forum for electrical and facilities management professionals has been established to assist in developing and deploying energy-effeciency strategies.
Measurement current transformers
01 January, 2009 | Supplied by: WF Energy Controls
WF Energy ControlsThe Series 27 range of measurement current transformers is available in six window sizes with hole diameters from 32 to 112 mm and ratings from 20 to 3000 A to suit a range of applications from panel metering to energy management input.