Baur KSG 100 cable identifier
07 March, 2011 byThe Baur KSG 100 cable identifier is suitable for use by power companies, maintenance companies and industrial electricians. The tracer is suited to single- and multi-core cables, paper insulated lead sheathed, XLPE and other insulation material cables. The cable identifier can also be used for phase identification. The system comprises a transmitter and receiver, the latter being supplied with a Rogowski coil.
Megger three-phase transformer tester
24 February, 2011 byAvailable to rent, the Megger three-phase transformer tester is a stand-alone or remote-controlled transformer turns ratio test set that measures ratio, phase deviation and exciting current with accuracy.
Ideal Industries industrial-grade True RMS TightSight clamp meters
15 February, 2011 byIdeal Industries’ industrial-grade versions of its True RMS TightSight clamp meters are suitable for demanding applications where accuracy, reliability and durability are required.
Fluke VoltAlert 2AC non-contact voltage tester
14 February, 2011 byThe 2AC has been added to the VoltAlert AC non-contact voltage tester range. It is easy to use and tests for energised circuits and defective grounds. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip or power cord where voltage is present.
Fluke 233 digital multimeter
14 February, 2011 byThe Fluke 233 digital multimeter is claimed to be the first digital multimeter with a detachable wireless display.
Fluke 27 II and 28 II digital multimeters
14 February, 2011 byThe Fluke 27 II and 28 II digital multimeters, suitable for operating in harsh conditions, are IP67 rated for water and dust resistance and offer an extended operating temperature range of -15 to +55°C.
Fluke 1555 and 1550C insulation testers
14 February, 2011 byThe 1555 and redesigned 1550C insulation resistance testers are designed for a wide range of diagnostic and predictive maintenance programs.
Fluke 1650B series installation tester
14 February, 2011The 1650B series installation tester provides two measurements at once and a dual display. PEFC/PSC and loop impedance are measured and displayed in parallel, which is claimed to save more than 50% of test time compared to other loop testers.
Fluke ScopeMeter 190 Series II handheld portable oscilloscopes
07 January, 2011The ScopeMeter 190 Series II handheld portable oscilloscopes are claimed to be the first four-channel scopes suitable for harsh industrial environments and safety rated for CAT III 1000V/CAT IV 600 V environments.
Agilent U1270 series handheld digital multimeters
01 January, 2011 byThe U1270 series handheld digital multimeters (DMMs) have a wide range of measurement capabilities, including feature sets that are found only in higher-end industrial handheld DMMs.
Why measure low resistance?
06 December, 2010Measuring low resistance is an important electrical test because it helps identify components where the resistance has exceeded acceptable values, threatening several potential negative outcomes. These could include overheating, energy loss, protective fault device malfunction, poor grounding and catastrophic failure during power surges. Test results can be used to identify changes caused by fatigue, corrosion, vibration, temperature or other conditions that may occur at the site.
Vivax VLOCPRO cable location system
25 November, 2010 byAvailable to rent, the Vivax VLOCPRO cable location system is a highly accurate pipe and cable location system. It has an intuitive menu system for easy configuration of the features users require.
Megger DLRO200 digital low resistance ohmmeter
16 November, 2010 byAvailable to rent, the Megger DLRO200 is a digital low resistance ohmmeter that measures resistances between 0.1 µΩ and 1 Ω at high currents.
AEMC handheld graphic MTX mobile multimeters
08 November, 2010 byThe AEMC handheld graphic MTX mobile multimeters have a resolution of 100,000 counts, 0.02% basic accuracy and up to a 200 kHz bandwidth. They feature a multiposition screen and push-button function selection and are suitable for both benchtop and handheld use. Model MTX3283B-BTCOMCM also features Bluetooth connectivity.
Fluke clamp meter range
08 November, 2010The Fluke range of clamp meters is designed to meet requirements for testing and maintaining electrical systems, industrial equipment, and commercial and industrial HVAC equipment.