Electrical distribution

Field termination M12 connector

09 July, 2009 | Supplied by: Harting (HK) Limited

The Field termination M12 connector enables the installer to choose between two different kinds of termination methods, making it adaptable to suit differing field situations and conditions. A wide range of shielded cables can be terminated onto the connector.


Docking station connector

09 July, 2009 | Supplied by: Harting (HK) Limited

The Han-Modular docking frame enables a docking connector in the IP20 range to be set up without a housing, for use in insertion processes, such as racks in switch cabinets, that are not hand guided.


Liquid-tight tubing and fittings

09 July, 2009 | Supplied by: NPA Pty Ltd

The Heyco range of Flex III liquid-tight tubing and fittings has been expanded with the release of 3/8- and 1-inch sizes.


Switch cover plates

09 July, 2009 | Supplied by: Legrand Australia P/L

The Linea Soft-Touch cover plates are a series of coloured fascias that can be snapped onto the Linea GPOs and switch plates, maintaining their low 4 mm thick profile.


Low harmonic drives

09 July, 2009 | Supplied by: Danfoss (Australia) Pty Ltd

The VLT low harmonic drive eliminates the harmonic disturbances on the supply grid by actively imposing currents into the grid so that the high-quality sine wave of the grid current is restored.


Cable bushings and grommets

09 July, 2009 | Supplied by: NPA Pty Ltd

The Heyco Products LabKit provides wire protection for cable entry points into prototype development of electrical and electronic systems and equipment.


DC-DC converters

09 July, 2009 | Supplied by: Powerbox Australia Pty Ltd

The Vicor DC-DC 28 VDC input family has been expanded with the addition of eight wide-input Micro DC-DC converters.


Quick-disconnect sensors

09 July, 2009 | Supplied by: Turck Australia Pty Ltd

The range of FM-approved 12, 18 and 30 mm 3-wire DC barrel sensor and cordset combinations has been expanded to include quick-disconnect sensors that may be used in Class I, Division 2, Groups A, B, C and D environments when equipped with a Turck lokfast guard. Sensors with potted-in cable for use with conduit are also FM approved for these locations.


Chemical resistant connectors

09 July, 2009 | Supplied by: Soanar Limited

The Anderson Power Products CR-SB (chemical resistant) SB range of high-current, quick-disconnect power connectors was developed for industrial applications that require robust connector solutions resistant to environmental factors that commonly degrade standard products, leading to eventual failure.


Q25L magnetically actuated linear displacement sensor

09 July, 2009 | Supplied by: Turck Australia Pty Ltd

The Q25L sensor is a magnetically actuated linear displacement sensor designed to detect piston position on pneumatic cylinders.


AC power load

08 July, 2009 | Supplied by: AEMC Instruments

The 3091LD AC power tester is designed to provide precisely controlled nonlinear loads for testing AC power generation equipment such as UPSs, AC sources, electrical switches and circuit breakers.


Electrical ground test kit

08 July, 2009 | Supplied by: AEMC Instruments

The Tower and Substation GroundFlex Field Kit includes the GroundFlex Adapter model 6474 and Ground Resistance Tester model 6472 to test ground resistance of individual power transmission tower legs and total resistance without disconnecting the overhead ground wire. It is designed to save time and money and enhance safety for operators.


Power quality monitor

08 July, 2009 | Supplied by: Westek Electronics Pty Ltd

The KoCoS EPPE C8 power quality and power line monitor is a comprehensive electrical analyser in a panel-mounting instrument package suitable for applications that include busbar, feeder and individual load monitoring and power quality analysis.


AC/DC power source

08 July, 2009 | Supplied by: Powerbox Australia Pty Ltd

The Compact iX Series AC and DC power source addresses increasing demands on test equipment to perform additional functions. Many components in the device are shared between the AC/DC source and the power analyser.


Blade heads for punch-down tool

08 July, 2009 | Supplied by: Fluke Networks

A series of interchangeable blade heads for the JackRapid termination tool that support ADC TrueNet KM8 and Copper Ten style cable jacks has been added to list of jack styles the termination tool supports.


  • All content Copyright © 2024 Westwick-Farrow Pty Ltd