Cable bushings and grommets
09 July, 2009 | Supplied by: NPA Pty Ltd
The Heyco Products LabKit provides wire protection for cable entry points into prototype development of electrical and electronic systems and equipment.
High-density power hub
09 July, 2009 | Supplied by: Pepperl+Fuchs (Aust) Pty Ltd
The FieldConnex 500 mA high-density power hub is an addition to the FieldConnex fieldbus interface products, designed for fast installation and reliable long-term operation in a fieldbus infrastructure.
Energy storage batteries
09 July, 2009 | Supplied by: Valen Power Pty Ltd
The SEC TSG range of 12 V sealed lead acid batteries deploys Monobloc Catalyst technology for long-life operation, thereby combining the safety and low-maintenance advantages of sealed lead acid batteries with the long life of normal lead acid batteries.
Transformer analyser
09 July, 2009 | Supplied by: Power Parameters Pty Ltd
The Serveron continuous, online, dissolved gas analysis monitor for transformers is available in two models, both based on closed-loop gas chromatography.
Liquid-tight tubing and fittings
09 July, 2009 | Supplied by: NPA Pty Ltd
The Heyco range of Flex III liquid-tight tubing and fittings has been expanded with the release of 3/8- and 1-inch sizes.
Watertight enclosures
09 July, 2009 | Supplied by: Hammond Electronics Pty Ltd
The 1457 extruded aluminium family of small enclosures has been expanded with the introduction of RFI-screened IP54 environmentally sealed versions. The 1457 E series is designed to house PCBs and small electronic, electrical or pneumatic components.
Field termination M12 connector
09 July, 2009 | Supplied by: Harting (HK) Limited
The Field termination M12 connector enables the installer to choose between two different kinds of termination methods, making it adaptable to suit differing field situations and conditions. A wide range of shielded cables can be terminated onto the connector.
Strain gauge signal conditioner
09 July, 2009 | Supplied by: Weidmuller Pty Ltd
The ACT20P-Bridge strain gauge signal conditioner and isolator provides four switch-selectable input ranges of 0 to ±10, 20, 30 and 50 mV and proportional analog output of between 0-22 mA with loads of <600 Ω, and 0-11 V with loads >1 kΩ. Accuracy is claimed as being better than 0.05%, with a temperature drift of better that 50 ppm over the range of -40 to +70 °C.
Q25L magnetically actuated linear displacement sensor
09 July, 2009 | Supplied by: Turck Australia Pty Ltd
The Q25L sensor is a magnetically actuated linear displacement sensor designed to detect piston position on pneumatic cylinders.
Quick-disconnect sensors
09 July, 2009 | Supplied by: Turck Australia Pty Ltd
The range of FM-approved 12, 18 and 30 mm 3-wire DC barrel sensor and cordset combinations has been expanded to include quick-disconnect sensors that may be used in Class I, Division 2, Groups A, B, C and D environments when equipped with a Turck lokfast guard. Sensors with potted-in cable for use with conduit are also FM approved for these locations.
Chemical resistant connectors
09 July, 2009 | Supplied by: Soanar Limited
The Anderson Power Products CR-SB (chemical resistant) SB range of high-current, quick-disconnect power connectors was developed for industrial applications that require robust connector solutions resistant to environmental factors that commonly degrade standard products, leading to eventual failure.
DC-DC converters
09 July, 2009 | Supplied by: Powerbox Australia Pty Ltd
The Vicor DC-DC 28 VDC input family has been expanded with the addition of eight wide-input Micro DC-DC converters.
Outdoor sensor
08 July, 2009 | Supplied by: Legrand Australia P/L
Aquascan is a weatherproof movement sensor that has been designed to act as an added safety measure for the exterior of a home.
Power quality monitor
08 July, 2009 | Supplied by: Westek Electronics Pty Ltd
The KoCoS EPPE C8 power quality and power line monitor is a comprehensive electrical analyser in a panel-mounting instrument package suitable for applications that include busbar, feeder and individual load monitoring and power quality analysis.
Blade heads for punch-down tool
08 July, 2009 | Supplied by: Fluke Networks
A series of interchangeable blade heads for the JackRapid termination tool that support ADC TrueNet KM8 and Copper Ten style cable jacks has been added to list of jack styles the termination tool supports.
